Posted on February 21, 2019


Hyperion g – read user manual online or download in PDF format. Pages in total: The Hyperion g linear imaging scanner boasts class-leading durability. Compatible with Remote MasterMind scanning management software. View and Download Honeywell Hyperion g user manual online. General Purpose Handheld Linear Scanner. Hyperion g Scanner pdf manual.

Author: Vutaxe Togal
Country: Bulgaria
Language: English (Spanish)
Genre: Sex
Published (Last): 4 May 2004
Pages: 123
PDF File Size: 12.14 Mb
ePub File Size: 13.95 Mb
ISBN: 113-6-52259-979-7
Downloads: 80832
Price: Free* [*Free Regsitration Required]
Uploader: Bajind

What is the range of possible values for Codabar Coding Enable? Programming the Interface – Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. If this bar code is read: Replacing The Interface Cable The interface cable is designed to be field replace- able.

Resetting The Standard Product Defaults 5. Disclaimer Honeywell International Inc. Connecting with RS Serial Port 1. Scan three numeric bar codes on the inside back cover to program the scanner for your terminal ID you must enter 3 digits.

Scan the Hands Free Time-Out bar code, then scan the time-out duration frommilliseconds from the inside back cover, and Save.

To change the number of beeps, scan the bar code below and then scan a digit bar code and the Save bar code on the inside the back cover of this manual. Tighten the two screws to secure the connector to the port. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology.


HII extends these warranties only to the first end-users of the products. Examples Of Query Commands Examples of Query Commands In the following examples, a bracketed notation [ ] depicts a non-displayable response. When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this charac- ter at the end of the scanned data.

See the Symbology Charts page A-1 for the single character code that identifies each symbology. Manual Trigger Default Automatic Trigger This unit has been tested with cables less than 3 meters. Page 76 The data is output as: If you make an error while scanning the letters or digits before mwnual Savescan Discard, scan mnaual correct letters or digits, and Save again. When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data.

Cable replacement instructions are on page Beeper Pitch — Error The beeper pitch codes modify the pitch frequency of the sound the scanner emits when there is a bad read mannual error. Page 83 FB Example: Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language.

Code 11 Mamual Length Scan the bar codes below to change the message length. This selection can be used if you have an IBM AT style terminal and the system is dropping characters. If you need to read codes that lead with the 1 number system, use the UPC E1 selection.

Hands Free Time-Out Reread Delay This sets the time period before the scanner can read the same bar code a sec- ond time. Table of Contents Add to my manuak Add.


Honeywell Hyperion 1300g User Manual

When in serial mode, 1300h scanner scans until a bar code has been read or until the deactivate command is sent. This includes but is not limited to: Limited Warranty Honeywell International Inc.

Page 70 4 – Codabar Message Length Scan the bar codes below to change the message length. User-specified Reread Delay User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay frommilliseconds by scanning digits from the inside back cover, then scanning Save. For exam- ple, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. Query Commands Several special characters can be used to query honeywe,l device about its settings.

Honeywell Barcode Reader g User Guide |

Refer to Chapter 9 for settings and defaults. Don’t show me this message again.

Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. This bar code sets the baud rate to bps and the data format to 8 data bits, no parity, 1 stop bit. This includes but is not limited to: Output Sequence Editor The breakdown of the command line is shown below: Using the bar code above: