Posted on February 28, 2019


HBM. A en. 1. Scope of supply. • Digital torque transducer (rotor and stator). • T12 Mounting Instructions. • Quick Start Guide for installing the T T12 CANbus/PROFIBUS. HBM. A en. CANopen interface. The CANbus is connected via male device connector 4 or 5. A maximum of. 32 CAN. The innovative digital torque transducer T12 is an ultra-high precision torque transducer for test benches and industrial use.

Author: Tygozragore Milkree
Country: Australia
Language: English (Spanish)
Genre: Career
Published (Last): 16 June 2015
Pages: 390
PDF File Size: 14.90 Mb
ePub File Size: 16.35 Mb
ISBN: 958-1-31463-735-3
Downloads: 50508
Price: Free* [*Free Regsitration Required]
Uploader: Dilrajas

T12HP – Technische Zeichnung. Highest Efficiency with Maximum Precision. Message 8 of Please send me a quote for T12HP further information. Its superior basic accuracy guarantees precise values over the entire measurement range.

Its a very expensive device! T12 Assistant didn’t show any spikes. So a continuous read works correct?

T12HP – Technical Drawing. Anke Thanks for the information. Automotive and Embedded Networks: The following overview opens up. HBM is offering you advanced torque calibration facilities for your torque sensors up to kNm.

Individual offer Technical advice Fast response. Due to its superior temperature stability with a TC0 of 0. Could you post the code? The T12HP torque transducer offers exceptional precision and superior performance for dynamic measurements in test benches to increase efficiency and optimize functionality. In case the file is not available yet, it can be downloaded from the HBM Support site.

Message 1 of The broadcasting method didn’t produce any kind of spiking in the torque value but the speed value acts like the way I mentioned in my previous posts. Message 6 of So far I’m experiencing some difficulties: Message 10 of The situation is actually quite frustrating since the program works in principal, but the more trivial part of tuning the measurement rate down causes trouble we can’t get our hands on.


The first method PDO1 sounds a bit more promising now that I’ve gone back and read the original post. Me and my colleague ran some more tests with the programs and the results are: We are upgrading from Method B assigned losses to Method A which requires us to measure torque and speed under different load conditions to determine the stray losses The present measurements are processed in LabVIEW 7, using GPIB and Serial instruments to get power, voltage, current and speed corrected for mains frequency.

Is it applied before everything else in the case structure or after all else has been done?

Automotive and Embedded Networks

Same thing with PDO2. Probing about in the dll files with a “Call Library Function” node, indicates that there are some appropriate links, such as Read and Write and Status. If we don’t slow the measuring down, for example measurements that last for several hours would result in massive logfiles.

I separately read the values of torque and rot. By double-click on the Gateway the network is searched for devices. Precision at bbm best: Remember to have the device description file installed in advance, as mentioned before in this Technote.

Thanks for your interest in our problem! How to check the Baudrate of the PMX is explained in the following. On second try I used queries.


If that wait is taken away and deleted, the program actually gets the value of rotational speed properly, but even with the present ms wait the read fails somehow and the rotational speed value freezes to the value of the first read.

The following overview is shown, where the sensor values are displayed. Even if we adjust the low-pass filter, the spikes remain.

The QuantumX MXB digital pulse and frequency module acquires rotational speed, torque, angle, position, displacement, pulse width modulation precisely. Contact us Please send a message and a representative will contact you shortly.

I shall investigate the hardware required. So, any ideas how to make this work? If I monitor the bus with PcanView, it shows that the speed value is indeed there, only the read fails. Experienced users are free to adopt a different approach.

HBM Torque Sensor T12 – Exxel Technology Pte Ltd – Your Premium Contract Manufacturing Partner

Please unzip all files before starting the installation. It is suitable for test bench concepts with challenging torque and speed measurements. The non-contacting transducer combines the gbm of digital signal conditioning with the measurement accuracy of a carrier-frequency amplifier without data or accuracy loss. How is the wait actually applied?